EliteDubs.Com
February 11, 2012, 06:29:16 AM *
Welcome, Guest. Please login or register.

Login with username, password and session length
   Home   Help Search GoogleTagged Login Register  
EliteDubs.Com > Elitedubs Motorsports > Dyno's > new dyno...need some help
Pages: [1]   Go Down
« previous next »
  Print  
Author Topic: new dyno...need some help  (Read 2130 times)
puredrive
n00b and a half
**
Offline Offline

Posts: 44
« on: May 01, 2005, 05:06:25 PM »
I went to Colvin automotives yesterday since I was just in the neighborhood . wanted to get a baseline dyno on my new GT30R...all runs were made at 20psi  93OCT

settings on REVO

HB=9
HT=3

first run=338whp  
sec. run=296whp
third run=306whp



I din't have my laptop with me. so i did not take down any logs..but why woud there be such a drop on hp??  could it be timming pull?


any advice would be apreciated
Logged
www.europeanag.com

yeah...its stock!!
mj6234
Rookie
***
Offline Offline

Posts: 174
« Reply #1 on: May 01, 2005, 05:08:42 PM »
Nice #. How long did you wait between runs? What IC? Could be heat soak.
Logged
Don®
1.8T Illuminatus
Global Moderator
Master
****
Offline Offline

Posts: 1017
« Reply #2 on: May 01, 2005, 05:14:45 PM »
I know you have no logs but I think the timing is set a little low...and your AFR is a little lean if it were pulling timing it may have been b/c of this fact.

What's your FP set at?...
Logged
donr@unitronic.ca

SEM Motorsports | QED Engine Forum
puredrive
n00b and a half
**
Offline Offline

Posts: 44
« Reply #3 on: May 01, 2005, 05:18:53 PM »
Quote from: mj6234
Nice #. How long did you wait between runs? What IC? Could be heat soak.


5min..i guess

I a running a greddy 31 FMIC..the outside temp was about 78F  so i am sure it was not heat soak.  kinda cofused about it..
Logged
www.europeanag.com

yeah...its stock!!
puredrive
n00b and a half
**
Offline Offline

Posts: 44
« Reply #4 on: May 01, 2005, 05:24:58 PM »
Quote from: DonR
I know you have no logs but I think the timing is set a little low...and your AFR is a little lean if it were pulling timing it may have been b/c of this fact.

What's your FP set at?...


48psi off vac


so your suggestion would be to run a higher timming map off the SPS3?


this was the same FP when i ran


the dyno below was done in Houston at carboy..they AF sniffer is off by .5

Turbo GT2871R .82AR  race gas mix
Logged
www.europeanag.com

yeah...its stock!!
Bastard
2.7t Masta
Global Moderator
Padawan
****
Offline Offline

Posts: 550
« Reply #5 on: May 01, 2005, 05:50:54 PM »
get better software.
Logged
GTi30R
n00b and a half
**
Offline Offline

Posts: 59
« Reply #6 on: May 02, 2005, 01:27:08 AM »
nice numbers for 20 psi....im hoping for about 350 and alittle change on 22 psi...we will see....when are you seeing spool?
Logged
GT30R-12
puredrive
n00b and a half
**
Offline Offline

Posts: 44
« Reply #7 on: May 02, 2005, 03:10:07 AM »
what software are you using?

it comes at about 4.5k

here is a small vid of th run

click and save as

http://www.hostdub.com/albums/puredrive/MVI_0889.avi
Logged
www.europeanag.com

yeah...its stock!!
GTi30R
n00b and a half
**
Offline Offline

Posts: 59
« Reply #8 on: May 02, 2005, 08:24:13 AM »
i have the newest version of revo BT 440@4bar program....and i have 580's on it currently...im seeing spool at about 4k now
Logged
GT30R-12
puredrive
n00b and a half
**
Offline Offline

Posts: 44
« Reply #9 on: May 02, 2005, 03:00:04 PM »
actually I am spooling a little sooner then I thought maybe 4300 RPM

I can maybe get it to spool sooner if I do some adj to the profec

are you running a Profec?

what are your settings?
Logged
www.europeanag.com

yeah...its stock!!
Pages: [1]   Go Up
  Print  
GoogleTagged: gt30r

« previous next »
 
Jump to:  

Powered by MySQL Powered by PHP Powered by SMF 1.1.16 | SMF © 2011, Simple Machines Valid XHTML 1.0! Valid CSS!